Showing all 15 results
100K OHM NTC Thermistors For Reprap 3D Printer
100K OHM NTC Thermistors For Reprap 3D Printer for temperature sensor is one where the thermistor chip is welded with leads by alloy soldering process, then partially treated by glass sealing. The element has a bead form with good stability, … Continued
3D Printer Controller Board RAMPS 1.4 Arduino Mega Shield RepRap
3D Printer Kit RAMPS 1.4+ Mega 2560 + 5* A4988 LCD 128*64
3D Printer Mechanical Limit Switch Module With Wire
3D Printer Mechanical Limit Switch Module With Wire The mechanical end stop uses a lever switch to detect when it is activated . The switch is wired up so that when activated , it pulls the signal to LOW . … Continued
3D Printer Ramps 128X64 Full Graphic Control Board
This Smart Controller contains a SD-Card reader, an rotary encoder and a 128×64 LCD display. You can easy connect it to your Ramps board using the “smart adapter”. After connecting this panel to your Ramps you don’t need your pc … Continued
3D Printer Ramps 20X04 LCD Smart Controller
3D Printer Ramps 20X04 LCD Smart Controller The intelligent controller includes an SD card reader, rotary encoders and a 20-character × 4 line LCD display. You can easily connect it to your RAMPS 1.4 board using “smart adapter” included. This … Continued
A4988 Stepper Driver With Heatsink
This A4988 Stepper Driver With Heatsink is used to control stepper for various electronic project. A4988 IC can drive 2A per phrase of the stepper Simple step and direction control interface Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and … Continued
Arduino 3D Printer Controller Kit – Mega 2560 Board+128*64 LCD+RAMP1.4
Cartridge Heater 6mm For 3D Printer-12V/40W
Cartridge Heater 6mm For 3D Printer-12V/40W Increases the reliability of extruder with this heater cartridge and also it heats up faster. It fits nicely in one’s extruders, hence is an easy replacement. Features: Voltage: 12V Power: 40W Wire length: 1m … Continued
Cartridge Heater 6mm For 3D Printer-24V/40W
Cartridge Heater 6mm For 3D Printer-24V/40W Increases the reliability of extruder with this heater cartridge and also it heats up faster. It fits nicely in one’s extruders, hence is an easy replacement. Features: Voltage: 24V Power: 40W Wire length: 1m … Continued
CNC Shield V3 + 4*A4988 Stepper Driver for RAMPS 1.4 Reprap 3D Printer
this expansion board as a driver expansion board, can be used for engraving machines, 3D printers. It is a total of four slots, can drive four A4988 stepper motor. Each road stepper motors only need two IO ports. In other words, six … Continued
Easy Driver Stepper Motor Driver A3967
The EasyDriver Stepper Motor Driver A3967 is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). The … Continued
MACH3 Interface Board CNC 5 Axis With Optocoupler For Stepper Motor Driver
- Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software.
- USB power supply and peripherals power phase are separate to protect computer security.
- All the signals are to-isolate which can protect your computer security.
- 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc.
- Wide input voltage range: 12-24V, and with anti-reverse function.
- One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.